All types of masonry units used as cladding, infill, or exposed wall structure. Includes a variety of masonry units, including adobe bricks and blocks, burnt clay bricks and blocks, stone, ceramic tile. It is often difficult to identify type of masonry units once the walls have been covered by plaster. These walls can be in the form of veneers, cavity walls, infill walls, as well as all of these materials used as Wall structure (a part of the Lateral Load-Resisting System), and where they are not covered by another material.

EWMA_Berkeley_USA_BrzevS_1

Stone masonry at the ground floor level and brick masonry above, Berkeley, California (S. Brzev)

EWMA_Canada_McEwen_5

An older partially demolished multi-wythe brick masonry wall in Vancouver, Canada (B. McEwen)

EWMA_Charleson_1

An exterior masonry wall may be a part of the cavity wall system, which consists of two masonry walls separated by an air gap; usually, one wall is load-bearing while the other is veneer (cladding). These walls may be connected by metal ties, and horizontal reinforcement may be provided (A. Charleson)

EWMA_NewZealand_Holmes_1

An illustration of cavity wall construction in New Zealand circa 1960 - note an interior (loadbearing) wythe and an exterior (veneer) wythe separated by a 50 mm air gap; the wythes are connected by galvanized wire ties (Holmes,I.L., Concrete Masonry Buildings in New Zealand, Proceedings of the 3rd World Conference on Earthquake Engineering, Session IV: 244-255,1965 - reproduced with the permission of the International Association for Earthquake Engineering)

EWMA_NewZealand_Centeno_1

Concrete block cavity walls damaged in the 2011 Christchurch, New Zealand earthquake: the photos show damage of both exterior and interior wall wythes (J. Centeno)

EWMA_Canada_McEwen_1

Masonry veneers are common exterior walls in Canada and the USA; a masonry veneer is a single-wythe brick masonry wall securely fastened to a structural backing (e.g. concrete masonry block wall, steel or wood stud framing). A veneer can be attached to structural backing by means of metal ties (B. McEwen, Canada; hyperlinked drawings courtesy of Masonry Institute of BC)

EWMA_Canada_McEwen_2

A diagram showing layered construction of a concrete block masonry backup wall with clay brick masonry veneer and insulation in between (web link permission courtesy of Masonry Institute of BC, Canada)

EWMA_Canada_McEwen_3

The exterior walls shown on the top photos look like loadbearing brick masonry construction. The photo on the left shows an older loadbearing brick masonry wall (built between 1900 and 1950), while the photo on the right shows a wall in a modern building (built between 1990 and 2010) which has similar masonry detailing like older buildings. However, the exterior brick masonry wall is a veneer and the loadbearing wall is likely a wood frame. The wall has weep holes characteristic of veneer construction (see detail on the bottom photo). The photos were taken in Vancouver, Canada (B. McEwen)

EWMA_Canada_McEwen_4

A concrete brick veneer wall with weep holes (B. McEwen)

EWMA_Canada_Brzev_1

EWMA_Canada_Brzev_2

An example of a masonry veneer in a reinforced concrete building in Vancouver, Canada; veneer can be identified by weep holes, as shown in the photo (S. Brzev)

EWMA_Chile_BrzevS_1

Adobe masonry walls: exposed (during construction), Chile (S.Brzev)

EWMA_Peru_Loaiza_Blondet_1

Adobe masonry walls overlaid by plaster, Peru (C. Loaiza and M. Blondet, World Housing Encyclopedia Report 52)

EWMA_France_BrzevS_1

Stone masonry walls: dressed stone at the front facade and uncoursed stone masonry in the perpendicular direction, France (S. Brzev)

EWMA_Moncton_Canada_Brzev_1

Exposed brick masonry walls, Canada (S. Brzev)

EWMA_Moncton_Canada_BrzevS_1

Exterior stone masonry walls, Canada (S. Brzev)

EWMA_Portugal_Brzev_1

Many buildings in Lisbon, Portugal have glazed ceramic tiles bonded to exterior walls (S. Brzev)